How to Make a Mini Resin Koi Pond · Craftwhack

Did y'all know you wanted to make a mini epoxy resin koi pond earlier seeing this mail? Bet you didn't! Unless you've already seen some online and though they were the cutest things ever, similar I did!

Epoxy resin projects seem to accept grown in popularity, and for skillful reason. There is something so cool about existence able to encapsulate items in clear plastic forever!

With this project, yous also go to play with polymer dirt to brand the cute trivial koi fish!

It's definitely a multi-part craft project, merely this fiddling koi pond diy is so worth it when you see the finished product.

Supplies For Resin Koi Swimming

Stones (call back these rocks from garden stepping stones project?)

Hot glue gun

Cardstock or paper-thin

Squeeze glue (school glue is fine)

Sand

2-function resin

Polymer clay

Moss

Wood slice or lath (ours was nigh 10″ at the longest point)

Heat gun or torch for removing air bubbles from resin (I've seen people utilize hair dryers for this)

How to Make a Mini Koi Pond

Start out by hot-gluing stones in any shape you similar on a piece of cardstock.

Keep adding levels of stones to the previous one, filling in gaps and dips to maintain an even stone level.

Once dried, fill in any obvious gaps in the stones with hot gum. If y'all miss any gaps, you run the hazard of the resin leaking out when it comes time to cascade information technology.

Add some bottled glue to the inside bottom of the swimming and smooth it out with your finger or a spreader. Don't use hot glue for this because it dries too quickly and information technology's hot!

Put a handful of sand in the pond and spread it out over the glue and let dry. I as well added a stone to the middle of the pond at this point. Once dry out, dump out backlog sand that didn't stick to the glue.

Mix a small-scale amount of the two-part resin mix per the instructions– probably one:1, but check the instructions. This is for an initial layer of resin in the pond. Information technology should terminate up being about ⅛" to ¼" thick.

Sprinkle some more than sand into the curing resin to fill in whatsoever bare spots, so you have a overnice even layer of sand.

Read the instructions for the resin–to remove bubbling you'll need to add together a very pocket-sized amount of heat to the surface with a heat gun or a torch. This is a very quick step and literally takes virtually ½ second for the bubbling to disappear.

Making the Polymer Clay Fish

While that initial layer is drying, it'due south time to make the fish with polymer clay. The shape of the fish is upward to you– the internet is full of examples to follow. To get the marbling issue on the fish, accept a actually minor brawl of clay and press into the dorsum of the fish. Lightly wet your finger and rub the tiny ball into the fish. I fabricated little lily pads, and I've seen others add little flowers, frogs, and swimming grass.

Finishing upwards the Koi Pond

Once the fish are broiled and absurd, mucilage them on the resin surface and let dry. This style they won't motility when yous add the second layer of resin. Repeat the steps you took with the showtime layer.

I ended up with three layers of resin, making sure the final layer fully submerged the fish.

Once dry I used kitchen shears to cut the excess card stock and whatsoever leaked out resin away from the outside border of the pond.

I had a slice from a downed tree that I glued the swimming to, only y'all could use a square or rectangular piece of wood, too.

I and so added moss around the pod to cover up the lip of cardstock and hardened resin that was visible.

I added a few rocks to the moss, and the koi pond was set for brandish!

Pin it For Later

ritchienatted.blogspot.com

Source: https://craftwhack.com/how-to-make-a-mini-resin-koi-pond/

Share this post